 |
| | DAD3050: TOA WM360/4310 (for low DC microphones) | Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067. MicroDot to Mini-Jack. |
|
|
 |
| | DAD3051: Ramsa WX-RP410 (for low DC microphones) | Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067. MicroDot to 4 pin Hirose. |
|
|
 |
| | DAD3052: AKG PT 40 (for low DC microphones) | Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067. MicroDot toTA-3F Switchcraft. |
|
|
 |
| | DAD3053: Sabine SW70-T (for low DC microphones) | Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067. MicroDot to TA-4F Switchcraft. |
|
|
 |
| | DAD3056: Lectrosonics LM, SM and UM series (for low DC microphones) | Adapter for DPA Miniature Microphones with low DC, Type 4063?and 4067. MicroDot for TA-5F Switchcraft. |
|
|
 |
| | DAD3057: Zaxcom TRX900 Series (for low DC microphones) | Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 3-pin Lemo (Zaxcom) |
|
|
 |
| | DAD3058: Sony DWT-B01 | | Adapter for use with DPA's series of Miniature Microphones. |
|
|
 |
| | DAD4099 Adapter | MicroDot to XLR Connector with Belt Clip and Low-Cut Filter.
The DAD4099 is designed for use with Miniature Microphones from DPA only. Belt clip included.
The DAD4099 is active signal balanced which improves suppression of induced electromagnetic noise.
Common Mode Rejection Ratio (CMRR) is better than 60 dB from 50 Hz to 15 kHz. Phantom power must be 48 Volt ± 4 Volt to reach the full specifications, see diagram. |
|
|
 |
| | DAD5000: LEMO/Male XLR | DAD5000 is a passive connection adapter to use for the integrated cable solutions for D3 and S5 mounts. The small LEMO connector can run through the pipes and connects to XLR through this adapter. |
|
|
 |
| | DAD6001-BC: MicroDot to 3-pin XLR (P48) w. Belt Clip | Adapter for powering Miniature Microphones via standard P48 phantom power.
The DAD6001 is designed for use with Miniature Microphones from DPA only. Belt clip included.
The DAD6001 is active signal balanced which improves suppression of induced electromagnetic noise.
Common Mode Rejection Ratio (CMRR) is better than 60 dB from 50 Hz to 15 kHz. Phantom power must be 48 Volt ± 4 Volt to reach the full specifications, see diagram. |
|
|
 |
| | DAD6002: Sennheiser BF1083-U/BF1053-U | Adapter for use with DPA's series of Miniature Microphones. MicroDot to Coax Lemo |
|
|
 |
| | DAD6003: Sennheiser SK 50/SK 250/SK 2000/SK 3063/SK 5012, Trantec SD7000 Digital Wireless, Shure UR1MLemo3 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 3-pin Lemo (Sennheiser) |
|
|
 |
| | DAD6004: Audio Ltd. Tx 2000/Tx 2020/Tx 2040 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 4-pin Binder. |
|
|
 |
| | DAD6006: Beyerdynamic TS42/TS85/TS190 | Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067. MicroDot to TA-4F Switchcraft. |
|
|
 |
| | DAD6008: Sony WRT820/WRT860/WRT8 | Adapter for use with DPA's series of Miniature Microphones MicroDot to 4-pin Hirose |
|
|
 |
| | DAD6009: Samson CT-2/TX-3/UT4/UT5/UT6 | Adapter for use with DPA's series of Miniature Microphones
MicroDot to 6-pin Hirose.
Please note that for TX3 systems, bias level must be increased from 3V DC to 9V DC. |
|
|
 |
| | DAD6010: Shure PGX1/SC1/SLX1/ U1/ULX1/UR1/UT1, TOA WM4300 | Adapter for use with DPA's series of Miniature Microphones
MicroDot to TA4F Switchcraft |
|
|
 |
| | DAD6011: Vega T-66/T-677 & Shure U1L | Adapter for use with DPA's series of Miniature Microphones MicroDot to 4-pin Lemo Series S. |
|
|
 |
| | DAD6012: Lectrosonics M185 | Adapter for use with DPA's series of Miniature Microphones
MicroDot to TA-5F Switchcraft
DAD6012 is for high sound pressure level use as it has -20 dB attenuation.
DAD6021 (0 dB attenuation) is recommended for normal sound level use. |
|
|
 |
| | DAD6013: Micron TX501.x/TX502.x | Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 8-pin Lemo. |
|
|
 |
| | DAD6015: Vega T-37, U2020 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to TA4F Switchcraft. |
|
|
 |
| | DAD6017: AKG PT 60/80/81/ 400/4000 Samson UT1L, VT2L | Adapter for use with DPA's series of Miniature Microphones. MicroDot to TA-3F Switchcraft |
|
|
 |
| | DAD6018: Wisicom/Pastega TMA16/TMU20 (3 wire preset) | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 3-pin Fischer. |
|
|
 |
| | DAD6019: Sony Freedom WRT 805 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to Mini-Jack (with thread) |
|
|
 |
| | DAD6020: Telex ProStar UHF-UB12 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to TA 4F Switchcraft |
|
|
 |
| | DAD6021: AT: ATW-T101 (U100), Lectrosonics UHF systems (low level) | Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA 5F Switchcraft.
For normal sound pressure level (0 dB attenuation).
For high sound level (-20 dB attenuation) we recommend DAD6012. |
|
|
 |
| | DAD6022: Audio-Technica, ATW-T51 (1400 Series) | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 4-pin Hirose. |
|
|
 |
| | DAD6024: MicroDot to 3-pin XLR (P48) w. Mid Range Attenuation | Adapter for powering Miniature Microphones via standard P48.
MicroDot to XLR with mid range attentuation.
Designed for microphone placement on the human body. When placing a microphone on a performers chest, an acoustic lower midrange boost will occur resulting in a "muddy" and indistinct sound, compared to a free frontal placement. This adapter provides a 3 dB attenuation at 800Hz for added clarity when using a Miniature Microphone. |
|
|
 |
| | DAD6025: Micron Explorer Series/TX700 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 6-pin Lemo Series B |
|
|
 |
| | DAD6026: Beyerdynamic TS 500/600 (non OPUS), Trantec S5000 series | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 4 pin Lemo. |
|
|
 |
| | DAD6027: Beyerdynamic OPUS 100-200 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to Mini-Jack |
|
|
 |
| | DAD6028: Audio-Technica ATW-T75 (7000 Series)/ ATW-T210 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 4 pin Hirose. |
|
|
 |
| | DAD6030: Electro-Voice CSB-1000 (RE1/RE2), TELEX | Adapter for use with DPA's series of Miniature Microphones. MicroDot to TA 4F Switchcraft |
|
|
 |
| | DAD6032: Beyerdyn. OPUS 300/500/600/800/900, Mipro ACT-707T/TE/TM/TS/MT103/303/801/808 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to TA 4F Switchcraft |
|
|
 |
| | DAD6033: Audio-Technica ATW-T1000 D/ ATW-T310/AEW-T1000/ATW-T701 | Adapter for use with DPA's series of Miniature Microphones. MicroDot to 4 pin Hirose. |
|
|
 |
| | DAD6034: Sennheiser Evolution/G2, /X2 Digital Wireless Systems | Adapter for use with DPA's series of Miniature Microphones. MicroDot to Mini-Jack (with thread) |
|
|
 |
| | DAD6035: Audio Ltd. Mini TX | Adapter for use with DPA's series of Miniature Microphones. Miniature for 4-pin Lemo (short version) |
|
|
 |
| | DAD6036: Trantec S5.5 (UHF) | Adapter for use with DPA's series of Miniature Microphones. MicroDot to Switchcraft TA-4F. |
|
Adapters
Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067.
MicroDot to Mini-Jack.
Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067.
MicroDot to 4 pin Hirose.
Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067.
MicroDot toTA-3F Switchcraft.
Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067.
MicroDot to TA-4F Switchcraft.
Adapter for DPA Miniature Microphones with low DC, Type 4063?and 4067.
MicroDot for TA-5F Switchcraft.
MicroDot to 3-pin Lemo (Zaxcom)
MicroDot to XLR Connector with Belt Clip and Low-Cut Filter.
The DAD4099 is designed for use with Miniature Microphones from DPA only. Belt clip included.
The DAD4099 is active signal balanced which improves suppression of induced electromagnetic noise.
Common Mode Rejection Ratio (CMRR) is better than 60 dB from 50 Hz to 15 kHz. Phantom power must be 48 Volt ± 4 Volt to reach the full specifications, see diagram.
DAD5000 is a passive connection adapter to use for the integrated cable solutions for D3 and S5 mounts. The small LEMO connector can run through the pipes and connects to XLR through this adapter.
The DAD6001 is designed for use with Miniature Microphones from DPA only. Belt clip included.
The DAD6001 is active signal balanced which improves suppression of induced electromagnetic noise.
Common Mode Rejection Ratio (CMRR) is better than 60 dB from 50 Hz to 15 kHz. Phantom power must be 48 Volt ± 4 Volt to reach the full specifications, see diagram.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to Coax Lemo
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 3-pin Lemo (Sennheiser)
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 4-pin Binder.
Adapter for DPA Miniature Microphones with low DC, Type 4063 and 4067.
MicroDot to TA-4F Switchcraft.
Adapter for use with DPA's series of Miniature Microphones
MicroDot to 4-pin Hirose
Adapter for use with DPA's series of Miniature Microphones
MicroDot to 6-pin Hirose.
Please note that for TX3 systems, bias level must be increased from 3V DC to 9V DC.
MicroDot to TA4F Switchcraft
Adapter for use with DPA's series of Miniature Microphones
MicroDot to 4-pin Lemo Series S.
Adapter for use with DPA's series of Miniature Microphones
MicroDot to TA-5F Switchcraft
DAD6012 is for high sound pressure level use as it has -20 dB attenuation.
DAD6021 (0 dB attenuation) is recommended for normal sound level use.
MicroDot to 8-pin Lemo.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA4F Switchcraft.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA-3F Switchcraft
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 3-pin Fischer.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to Mini-Jack (with thread)
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA 4F Switchcraft
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA 5F Switchcraft.
For normal sound pressure level (0 dB attenuation).
For high sound level (-20 dB attenuation) we recommend DAD6012.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 4-pin Hirose.
Adapter for powering Miniature Microphones via standard P48.
MicroDot to XLR with mid range attentuation.
Designed for microphone placement on the human body. When placing a microphone on a performers chest, an acoustic lower midrange boost will occur resulting in a "muddy" and indistinct sound, compared to a free frontal placement. This adapter provides a 3 dB attenuation at 800Hz for added clarity when using a Miniature Microphone.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 6-pin Lemo Series B
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 4 pin Lemo.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to Mini-Jack
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 4 pin Hirose.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA 4F Switchcraft
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to TA 4F Switchcraft
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to 4 pin Hirose.
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to Mini-Jack (with thread)
Adapter for use with DPA's series of Miniature Microphones.
Miniature for 4-pin Lemo (short version)
Adapter for use with DPA's series of Miniature Microphones.
MicroDot to Switchcraft TA-4F.